Seasoft Pro/C3 3 mm Dry-Suit Hood for Full Face Mask (FFM)

Your Price:

$59.95 You save: $10.04 (14%)

List : $69.99

Seasoft : Picture 1 regular $59.95

About Seasoft Pro/C3 3 mm Dry-Suit Hood for Full Face Mask (FFM)

When Diving, the Deeper a diver goes the Colder it generally gets and with Increasing Pressure, a Typical Neoprene Hood gets thinner. If the Temperature is getting Colder and your Hood is getting thinner, you're going to get Cold. And, when you consider that 35% of Heat Loss is from the Head area, it seems like this would be a place to make sure you are Adequately-Protected to ensure Warmth and Comfort.

The SEASOFT Titanium PRO/C3 Hood has 4 different types of Nylon ll Neoprene including Compressed Neoprene for the Back-3 Panels of the Hood. This means that no matter how deep you go, they are still their Original-Thickness and working to keep you Warm! You will not find any Seams down the middle of the Chin either. This Seam, found in almost all Hoods today, can cause Jaw Fatigue. The Seam is there because it is less expensive to make a hood from just two halves. We do not believe that a hood is the place to go cheap.

The Hood has Titanium Flakes Poil Technology that creates 2-Layers of Titanium Foil that Reflects Cold away and Reflects your Heat in keeping you Warmer than Hoods without this Technology. The 3 mm material is going to Naturally-Fit and Stretch around your head better. This leaves less room for cold water to occupy UNDER your hood, this helps to maintain warmth as well. There are also two very Small-Holes for Air-to-Escape from the Inside-Crown of the Hood in case air enters your hood with a Thin-Baffle Built-Over the Holes to prevent Water from Entering.

The SEASOFT PRO / M3 3 mm Dry Suit Hood is a Commercial Dry Suit Hood designed to be worn with a Full Face Mask. The PRO/C3 has a Layer of Skin-In Neoprene on the Inside and on the Outside with a Layer of Tough Nylon in between these two layers. The Skin-In Neoprene allows the Hood to Seal to your Face and the Full Face Mask to Seal to the Hood. SeaSoft Pro/C3 Wetsuit Hood use 3 mm Neoprene with Glued and Sewn Seams for Strength and Durability. The Hood is available in sizes Medium, Large, X-Large and 2X-Large, is Black in Color and is covered by a 24 month limited warranty.

Warranty Information

This product has a limited warranty of 24 months.
(800) 939-5510

Seasoft Pro/C3 3 mm Dry-Suit Hood for Full Face Mask (FFM) Features

  • Specifically Designed for Full Face Mask Divers
  • 35% of Heat Loss is from the Head
  • Construction: 4 Different Types of Nylon ll Neoprene
  • Compressed Neoprene: Back 3-Panels of the Hood
  • Compressed Neoprene: Won't Get Thinner at Depth
  • Thicker Neoprene: Warmer Dive
  • No Chin Seam: Reduced Jaw Fatigue
  • Titanium Flakes Poil Technology: 2-Layers of Titanium Foil
  • Titanium Foil: Reflects Cold Away and Reflects your Heat In
  • 3 mm Naturally-Fit and Stretch Around Head Better
  • Small-Holes with Thin-Baffle on Inside-Crown Vent Trapped Air
  • Seams Glued and Sewn for Strength and Durability
  • Commercial Dry Suit Hood
  • Layer of Skin-In Neoprene on Inside and Outside with Layer of Tough Nylon in Between
  • Skin-In Neoprene allows Hood to Seal to Face and Full Face Mask to Seal to Hood
  • Sizes: Medium, Large, X-Large and 2X-Large
  • Color: Black
  • 2 Year Limited Warranty
Share this item: