The Zeagle Ranger LTD BCD is an advanced system that caters to every level of diving. The shoulder straps are designed with the new super duty airlock buckle that will swivel to Adjust the harness to contour the body and eliminate binding and restriction of movement at the chest and underarm areas. With the addition of harness type Webbing and a new threading arrangement the diver can easily add more D-rings and other accessories conveniently on the shoulder. This feature will now allow the technical and accessory minded diver to further set-up their BCD to what their needs for the type of diving they are doing. Zeagle has also added a right hand shoulder dump with a pull knob located conveniently on the inside edge of the right shoulder pad. The dump valve acts also as an additional Safety overpressure valve.
The Zeagle Ranger LTD is equipped with the personal fit system (PFS) modular sizing. The PFS allows for a custom fit and lets you change out specific sections of the BCD. The Zeagle Ranger LTD also has adjustable elastic waist panels and a lumbar pad that is permanently mounted in the rear of the vest section. The BCD is made from heavily reinforced 1050-Denier ballistic nylon, has 2 zippered utility pockets, 4 stainless steel D-rings on the shoulders (two adjustable), 2 stainless steel D-rings on the vest so there is plenty of storage space and accessory attachment points for all your gear.
This back inflation BCD provides 44lbs (20kg) of Lift and comes equipped with Zeagle s ripcord weight system. The ripcord system has a Soft Weight Capacity of 30lbs (13.6kg) of releasable weight and an additional capacity of 20lbs (9kg) rear trim weight that is non-releasable. Adjusting the BCD for a perfect fit the Ranger LTD has torso adjustable shoulder straps an adjustable sternum and waist straps all equipped with squeeze-style" side-release buckles for easy donning and doffing.
The Ranger LTD can accommodate single or twin tanks with 11" (27.8cm) spaced grommets for the twin cylinder mounting. Buoyancy control and trim is easy with the 2 lower rear, right shoulder overpressure relief/pull dump valves and Bx power inflator mechanism. The Bx power inflator makes preventative maintenance easy with its threaded lower mechanism that allows the attachment of a garden hose for fast and easy inner bladder rinsing. The Bx is also connected to a pull dump valve for rapid deflation. The BCD dry weight is 9.5lbs (4.3kg) it is available in multiple Sizes, comes with a comprehensive owner s manual, Low Pressure quick disconnect hose with 3/8" threads, and is covered by a lifetime limited warranty.
The Zeagle flat head LT is based on the flagship of Zeagle s regulator line; the Flat Head 7. Zeagle s Regulators are made in the USA, built under strict quality control in Zeagle s own factory, using state of the art equipment and procedures. The regulator is your single most important piece of gear. No matter what kind of diving you do, you can do it better with Zeagle. The Flat Head LT is very low in profile; barely extending above the tank valve and places the low-pressure hoses directly out to the sides, in a pattern preferred by many divers.
The black chrome plated marine brass first stage regulator body is a balanced diaphragm design, which is inherently environmentally sealed. The diaphragm membrane transmits the pressure changes to the internal mechanism eliminating the need for the surrounding water to enter the intricate mechanism. The benefit of this type of first stage design is that none of the internal parts are exposed to contaminants such as salt, sand, chlorine, or pool acids. These environmental contaminants cause corrosion and mineral deposits to form on the internal mechanism deteriorating regulator performance.
Zeagle s stainless steel high-pressure valve and advanced polymer Seat provides much greater reliability and service life compared to conventional designs, while improving responsiveness and performance at all breathing rates. With high performance porting in a balanced diaphragm design and an environment seal, makes this one clean regulator first stage that will give you years of corrosion free service. The Flat Head LT regulator has an Internal structure that allows for direct airflow through the 1st stage, providing outstanding performance. First Stage is equipped with 2 high-pressure ports and 5 low-pressure ports for mounting of gauges and additional accessory items such as an inflator hose and octopus regulator.
Zeagle s ZX second stage is lightweight, compact and comfortable, with diver adjustable resistance controls and free-flow control features. Specific design changes have created a regulator that is resistant to free-flow on the surface, yet has incredible smoothness and ease of breathing underwater. This pneumatically balanced downstream demand valve second stage regulator is manufactured from flexible thermoplastic, elastomeric polymer and silicone rubber. The standard hose measures 30" (76 cm) and is 3/8" threaded. The complete regulator weighs 41.3oz (1,170.3 g) with the hose, comes with a comprehensive owner s manual, is nitrox ready to 40% out of the box and is covered by Zeagle s lifetime limited warranty.