800.637.6880
212.645.1234
|
|
XS Scuba Worthington Cylinders LP Steel 2,400 psi (166 bar) Tanks
5
See More Similar
Scuba Tanks »
|
|
XS Scuba Worthington Cylinders LP Steel 2,400 psi (166 bar) Tanks
|
Our Price:
|
$324.95 - $424.95
|
SKU:
XSSLPT
In Stock
|
|
|
Questions about this item:
Shopper Is it safe to store a filled scuba tank inside a hot car for a couple hours? The UV index is so strong in FL I worry that I'll blow the valve. I like to check out the vis before lugging all my equipment to the water.. leaving filled tanks in my car makes me paranoid. I've been getting conflicting responses from my local dive shops.
SPENCER R Don't worry, hot cars will NOT cause valves to blow, no matter how long they are in the car.
RUSSELL L In Florida I would not store a filled tank in a car for a couple of hours. I had one burst disc blow in the back of my truck in the keys last year. I think it would even be more likely to blow in a hot car.
ANDRES M Tanks will stand some heat,but don`t force your luck .A few hours don`t hurt. But is better to keep the tanks in a well ventilated area. Steel tanks are much better than aluminum ones.
LUIS C I suggest you that never leave your filled tanks in the trunk at daylight. The only thing that can happen is the blow of the safety disk. But is better to avoid that.
LC
Shopper What are the dimensions for the 95 and 108 cu tanks?
LeisurePro S The 95 cu tank is 23.7 inches in height and 8 inches in diameter; the 108 cu tank is 26.5 inches in length and 8 inches in diameter.
Shopper Should I buy a low pressure or high pressure tank?
LeisurePro S Choosing a high pressure or low pressure tank all depends on the kind of diving you are planning on doing. For more information, check out this forum on chooseing a tank and jump to the section on pressure.
Shopper Can you please provide the detailed weight for each of the tanks please? 77cu, 85cu, 95cu and 108cu.
LeisurePro S Empty tank weights: 77cu = 32.5 lbs, 85cu = 34.3 lbs, 95cu = 41.9 lbs and 108cu = 45.9 lbs.
Shopper Are the 85's hydro-tested prior to shipping?
LeisurePro S Tanks are current but visual inspections are required to be done prior to filling only and cannot ship that way. We guarantee the tank will pass or it will be replaced.
Shopper What is the height width weight of the low pressure 131?
LeisurePro S The low pressure 121 tank measures 29.2 inches in height with an outside diameter of 8 inches and an EMPTY weight of 49.9 pounds.
Shopper Exactly what valve do you sell with your Worthington LP 108's,
LeisurePro S Thermo Valves
Shopper The Nitrox steel tanks. Can they be used for just air? Like the old steel tanks I used to use? I liked the no change in bouyancy and not as much to sink you. I know they are a little high vs.AL but just wondering.
LeisurePro S Yes, can be used with air only.
Warranty Information
This product has a limited warranty of 24 months.
www.xsscuba.com
(866) 977-2822
Whats in the box:Cylinder, Valve and Tank Boot The steel cylinders are manufactured at Worthington Cylinder's state of the art facility in Tilbury, Canada. The cylinders are manufactured using the Deep Draw and Ironing (DDI) process. Cylinders start from a circular plate of chrome-moly steel. Multiple draws on a hydraulic press transform the plate into an open ended shell. The shell is then closed, the neck is formed and the threads are machined. The DDI process produces the most consistence wall thickness resulting in the lightest weight, most efficient cylinders. This manufacturing process is what allows Worthington to supply cylinders with the best buoyancy characteristics for scuba diving. During the process of Hot Dip Galvanizing, the exterior of the Worthington steel cylinders are submerged into 840?F molten zinc. The process deposits a 5 - 8 mil thick zinc barrier to protect against the corrosive ocean environment. This layer of zinc metallurgically bonds to the steel cylinder. The Zinc will not chip and wear away like a painted zinc finish. XS Scuba is so confident that exterior rust will not be an issue; they guarantee it for the life of the cylinder. If the exterior of your XS Scuba HDG steel cylinder rusts, XS Scuba will correct it for as long as you own the cylinder, without cost to you. All the XS Scuba Worthington Cylinders are designed to be slightly negative at the end of a dive, unlike aluminum cylinders that provide positive buoyancy at the end of a dive, requiring the diver to wear added lead to compensate for the excess buoyancy. The XS Scuba Worthington Steel Cylinder allows you to wear less lead on all dives (for specific buoyancy characteristics see specifications). The interior of the cylinder is Highly-Resistant to Rust using a Phosphatized Finish. All Cylinders are Nitrox Cleaned and Sealed at the factory, free of hydrocarbons to a level of 40 mg per square meter and ready for pre-blended Nitrox up to 40% FO2. Cylinder comes equipped with the XS Scuba Pro Valve. The XS Scuba's Pro Valve is designed and manufactured for long life and heavy use. Valve is made of marine grade brass with triple bright chrome plating for long life protection in salt water. Precision Machined from high tension brass and chrome plated the valve stems will give years of service and corrosion free operation. Easy Grip soft rubber Safety Hand Wheel with Stainless Steel Insert ensures long life and large ribs make turning handle easy even when wearing gloves. This New Unique Safety Hand Wheel allows the diver to visually see if the valve is completely turned on and off with a set of colored rings that appear on the valve side of the hand wheel. If you see Red" the valve is off or not completely open. If you see Green" the valve is completely open and ready for diving. New hand wheel takes the guess work out of knowing your valve is fully open and ready for diving. Valve bonnets are O-ring sealed not copper crush washer sealed with extreme torque requirement. You won't need to Crank" on the valve when you open and close it with the 1.5-Hand Wheel Rotation from Full-On to Fully-Off. The Valves Seat Assembly is Teflon Coated for years of Smooth Operation and a One-Piece Safety Plug protected within the Valve Body guards against damage during transport. The Pro Valve will accommodate both Yoke and DIN Cylinders with its Removable 230 bar (3,336 psi) DIN Insert which can be removed using a 1/4" Hex Key Wrench. Vale has a 5/32" Hex Key Dip Tube and is Nitrox compatible up to 40%. Included with the Cylinder Valve Assembly is a Durable, Quality Self-Draining Designed Tank Boot with Hexagon Edge to prevent rolling while cylinder is lying down. The XS Scuba Worthington LP Steel is a Compressor-Friendly 2,400 psi (166 bars) Cylinder with a "Plus" rated for 10% overfill to 2,640 psi (182 bars) and are available in 4 sizes: LP85 cu ft (12.8 liter) with a 7.25" (18.4 cm) diameter, LP95 cu ft (14.8 liter), LP108 cu ft (16.8 liter) and an LP121 cu ft (18.9 liter) with 8.0" (20.3 cm) diameters. All cylinders are covered by a 24 month limited warranty. See preview of How a Worthington Steel Scuba Cylinder is Made When shipped the tanks valves will be removed and the tank will require re-inspection before being filled.
- XS Scuba Worthington Cylinders LP Steel 2,400 psi (166 bar) Tanks
- Complete Cylinder System: Tank, Valve and Boot
- Nitrox Ready Up to 40% FO2
- 2 Year Limited Warranty
- Cylinder:
- Material: Chrome-Moly Steel
- Deep Draw and Ironing (DDI) Process
- DDI: Produces Most Consistence Wall Thickness
- Lightest Weight, Most Efficient Cylinders
- Hot Dip Galvanizing
- Zinc Metallurgically Bonds to Steel Cylinder
- More Volume in Compact Cylinders
- Volume: LP85 cu ft (12.8 liter), LP95 cu ft (14.8 liter), LP108 cu ft (16.8 liter) and LP121 cu ft (18.9 liter)
- Length: LP85: 24.7" (62.7 cm), LP95: 23.7" (60.2 cm), LP108: 26.5" (67.3 cm) and LP121: 29.2" (74.2 cm)
- Diameters: LP85: 7.25" (18.4 cm), LP95,108 and 121: Diameter: 7.25" (18.4 cm)
- Weight (empty): LP85: 36.8 lbs (16.7 kg), LP95: 41.9 lbs (19 kg), LP108: 45.9 lbs (20.8 kg) and LP121: 49.9 lbs (22.6 kg)
- Buoyancy Full: LP85: -7.1 lbs (-1.4 kg), LP95: -10.1 lbs (-4.6 kg), LP108: -10.7 lbs (-4.9 kg) and LP121: -11.1 lbs (-5.0 kg)
- Use Less Lead than Aluminum Cylinder Diving
- Ultimate Weight to Capacity Ratios
- Manufactured to DOT Exemption and Canadian TC Permit
- Lifetime "Exterior No Rust" Warranty
- "Plus" Rated for 10% Overfill to 2,640 psi (182 bar)
- Compressor-Friendly, Lower Pressure
- Valve:
- XS Scuba Pro Valve
- Standard Yoke Outlet with Spin-Out DIN Insert
- Converts to 230 bar (3,336 psi) DIN Outlet
- 1/4" Hex Key Wrench Removable DIN Insert
- 3/4" - 14 NPSM Standard Inlet Threads
- 1.5 Hand Wheel Rotations from Fully-On to Fully-Off
- 5/32" Hex Key Dip Tube Included
- New Unique Color Coded Safety Hand Wheel (SHW)
- SHW: Red" Valve is Off or Not Completely Open
- SHW: Green" Valve is Completely Open and Ready for Diving
- Service Pressure: Up to 3442 psi (230 bars)
- Triple Bright Chrome Plated Marine Brass Body
- Chrome Plated Durable Brass Valve Stem
- Teflon Coated Brass Valve Seat with Nylon Seal
- O-Ring Sealed Bonnet
- Easy Grip Rubber Hand Wheel
- Tank Boot:
- Durable, Quality Self-Draining Designed Tank Boot
- Hexagon Edge: Prevents Cylinder from Rolling when Lying on Side
| Cylinder: | ---- | | Pressure | LP Steel 2,400 psi (166 bar) | | Diameter | LP85: 7.25" (18.4 cm)
LP95, 108 and 121: 8.0" (20.3 cm) | | Weight | (Empty) LP85: 36.8 lbs (16.7 kg), LP95: 41.9 lbs (19 kg), LP108: 45.9 lbs (20.8 kg) and LP121: 49.9 lbs (22.6 kg) | | Height | LP85: 24.7" (62.7 cm), LP95: 23.7" (60.2 cm), LP108: 26.5" (67.3 cm) and LP121: 29.2" (74.2 cm) | | Buoyancy Full | LP85: -7.1 lbs (-1.4 kg), LP95: -10.1 lbs (-4.6 kg), LP108: -10.7 lbs (-4.9 kg) and LP121: -11.1 lbs (-5.0 kg) | | Cylinder Nitrox Ready | Yes | | Valves: | ---- | | Material | Valve Body & Stem : Marine-Grade Chromed Brass
Hand Wheel: Rubber
Seat Assembly: Teflon Plated Brass Alloy with Nylon Seal | | Type (Yoke, DIN, Convertible) | Convertible | | Valve Nitrox Ready | Yes | | Thread Size | 3/4"-14 NPSM | | Weight [with packaging] | 85 cu ft. 12.8 liter: 40.1 lb, 95 cu ft. 14.8 liter: 47.6 lb, 108 cu ft. 16.8 liter: 50.85 lb, 121 cu ft. 18.9 liter: 53 lb |
8/5/2009 (1 of 2 customers found this review helpful) 5.0I might buy a bigger tank By rcarstop from Bel Air, MD About Me Recreational Diver - Diving Type:
- Open Water Diving
6/25/2009 5.0The next level of performance - Easy to Use
- Large Capacity
- Lightweight
- Diving Type:
- Drift Diving, Open Water Diving, Wreck Diving
4/28/2009 (2 of 3 customers found this review helpful) - Easy to Use
- Large Capacity
2/6/2009 (3 of 3 customers found this review helpful) By pelsung from Virginia Beach 10/22/2008 (1 of 1 customers found this review helpful) - Easy to Use
- Large Capacity
- Night Diving
- Open Water
- SCUBA Class's
- Wreck Diving
- Diving Type:
- Drift Diving, Night Diving, Open Water Diving, Rescue Diving, Spring Diving, Wreck Diving
|
|
|