The Spirit regulator is a time tested design. Used around the world in some of the most demanding conditions as the choice of diving resorts, rental departments and commercial divers. The Spirit is Factory cleaned and ready for Pre-Blended Nitrox Up to 40% FO2. Simple in Design, Low Maintenance and Value Priced. The First Stage Regulator is a Reliable, Non-Balance Fail-Safe Flow-By Piston Regulator Design. The First Stage has 4 Low Pressure Ports and 1 High Pressure Port... more
Tags: Essential Equipment,Xs Scuba Regulator,Spirit Regulator,Xs Scuba,Xs Scuba Spirit,Regulators,Xs Scuba Spirit Regulator
|
Studies have been performed showing a significant improvement in dry suit thermal protection can be achieved when using argon instead of air as a dry suit inflation gas. Overall, the total suit insulation increased by approximately 20%. If you Dive a Dry Suit and want to be warmer longer than you should be using an Argon Regulator System. Highland by XS Scuba's Argon Regulator is a complete regulator system set up specifically for use with Argon Gas. The First Stage is a Non-Balanced, Reliable and Simple Flow-By Fail Safe Piston Design that is factory set at 115 to 125 psi (7.9 to 8... more
Tags: XSSCARB, Highland Millworks, Regulators, Essential Equipment, Highland by XS Scuba Complete Argon Regulator Metric Gauge
|
The MC9 Hyper-Balanced Diaphragm Actuated 1st stage regulator has a lightweight body covered by a protective techno-polymer elastomer shell. The regulator is equipped with four low pressure and two high pressure ports. Internally the 1st stage is coated with an anti-friction anti-corrosion material that reduces resistance and allows the critical components to move freely. This makes the components perform and last longer between annual servicing and increases performance... more
Tags: CSBX9PK, Cressi, Regulators, Essential Equipment, Cressi XS Compact MC9 Regulator Pink Plate
|
The MC5 Hyper-balanced Diaphragm Actuated 1st stage regulator has a lightweight body covered by a protective techno-polymer elastomer shell. The regulator is equipped with three low pressure and one high pressure port. Internally the 1st stage is coated with an anti-friction anti-corrosion material that reduces resistance and allows the critical components to move freely. This makes the components perform and last longer between annual servicing and increases performance... more
Tags: CSBXS5, Cressi, Regulators, Essential Equipment, Cressi XS Compact MC5 Regulator
|
This specially designed hanger is built specifically to hang your expensive BC and Regulator System (Yoke or DIN). It allows proper drying and keeps them off the floor to prevent damage. XS Scuba's Basic BC Hanger is anything but basic! Hanger is constructed from Sturdy One-Piece Noncorrosive Plastic for Durability and long Life. With Tough X-Beam Design and a Beefy 1.0" (2.5 cm) Support Beams it won't matter how wet your gear may be. Hanger has Lower Hooks to Hold a Regulator by the Hoses so when stored on the hanger there is No Stress on the Important Hose Fittings. Hanger Measure 15.8" x 9... more
Tags: XSSB2XL, XS Scuba, Hoods, Exposure Protection, XS Scuba 2 mm Tropic Beanie 2X-Large
|
The XS Scuba BC Travel Hanger Folds-Up for Easy Storage, when on the road, or traveling to an exotic dive site, yet is ready to use when you get there. The Hanger's Folded dimensions are a Compact 5.4" x 8" x 2.5" (13.7 x 20.3 x 6.4 cm), when Unfolded the Hanger measures 15.75" x 8" x 6.25" (40 x 20.3 x 15.9 cm). Hanger is designed to ensure Quick Drainage and Drying, and is built not only for your BCD, but with the 2 additional Folding Arms will hold your regulator and accessories too. Hanger has Large Hooks to Retain Shoulders of the BCD, so you won't come back to find it on the ground... more
Tags: Xs Scuba Folding Bc Travel Hanger Yellow,Xs Scuba,General Accessories,Xs Scuba Hanger,Bc Hanger,Assorted Accessories
|
Keeping warm when diving can be one of the most difficult things to do. If you wear a dry suit you can remain warmer for longer periods of time then if you wear a wet suit, but even a dry suit can allow you to have heat loss. One way to increase the retention of body heat in a dry suit is to use argon gas to fill it rather than air or nitrox. Argon is a great insulator, being heavier then air or nitrox argon will keep you warmer longer. XS Scuba's Highland Dry Suit Inflation Kit can increase your bottom time by keeping your breathing gas for just that... more
Tags: XSSDSIK, XS Scuba, Tanks, Essential Equipment, Highland by XS Scuba Dry Suit Inflation Kit
|
Do you want to run two second stage regulators from one low pressure (LP) hose? XS Scuba's LP Hose Splitter can make this happen. This Durable Corrosion Resistant Chrome Plated Brass LP Hose Splitter allows you to route two Second Stage Low Pressure Hoses from one LP Hose or maybe you want to run an Inflator Hose and a Second Stage. Whatever 3/8" Threaded Hose Configuration you are looking to route can be accomplished with this Adapter... more
Tags: XSSLPH100, XS Scuba, General Accessories, Assorted Accessories, XS Scuba Miflex Low Pressure Hoses 100' 1200" Black
|
|