ERIC M Need the lenght

STANLEY S It fits both my HOG wing and my Dry Suit inflator, so it should fit a DiveRite, which has a standard fitting.

B H  I'm about 99% sure that it would work for you aswell.... I dive with this hose on my Deep Outdoors wings and my inflator is a Dive Rite. This hose is nice, a must have.

TIM J It is a true 26 inches plus 1/2 to screw into the first stage. looks good haven't used it yet.

RAYMOND C Measurement is from threaded fitting to slip on fitting.

Glenn o Hose dimensions?.... Not sure of the relevance of the questions. The hose is standard dimensions used on all BCD hose connections and, I believe, a standard size that fits the first stage. The hose comes in various lengths.

RUPERT M Tip to tip.

JASON D Better be on the safe side and assume length means the entire length including couplings.

Paco Z End to end, and it was a great purchase, I do recommendo it.

OLIVER F I allowed in my measurement the hose itself not the fittings. Suggest one would measure the old one and buy similar if that was good.

MICHAEL B The LP inflator hose will work with STANDARD quick disconnect for the BC inflate only. This inflator hose will not work with Air 2 type of inflators with octo. That quick disconnect is larger to draw more air threw it. Stick with the 22 inch for length.

MAHLON R the length of the inflator hose depends a lot on the bcd's inflator hardware. For instance my inflator hose fits perfectly on om BCD but is an inch or two too long on my daughter's. So not knowing the Length needed for the other bcd's it's hard to tell. Worst case is if it is too long you will just have an s shape, using up the excess, in the inflator hose and if too short it will kink the bcd's inflator tube a bit. I would try the 22 and go from there. Good Luck

STEPHEN H I think it would depend highly on the size of the BC and configuration of the 1st stage. Best to measure the existing one first, or compare how the 2nd stage hose length compares to the inflator unit on the BC and use that as a guide.

KHENG YEW T 22" is the typical length and should work with most BCDs. Having said that, I'm unfamiliar with the brands/models you mentioned having dived mostly backplates. I presume you have already ensured that the 22" would fit all the BCDs which you are using now by measuring the existing length of the various hoses in place whenever you used the said BCDs. You could go with the 26" just to play it safe but there will be an extra loop over your shoulder which makes it less streamline. Also, note that you would want a longer hose if you tend to use oversize hose protectors since they tend to curve the hose at a greater angle and hence would require a longer length to cover the same effective distance from your BCD to the inflator.

MICHAEL B The Tusa, Atomic and ScubaPro all has the same quick disconnect. This hose is for a BC and not for what you want to do. I bought the regular Phantom LP hose SKU: ICSPLPH. Then added the adaptor that should be on your old hose. You will need less hose length since the new thinner hose will flex more. Every set up is different but I bought a 22 inch and I am a big guy wearing a drysuit also. FYI I am a cert. Pro tech. and earning my Expert Cert. hopefully by March 2013. Hope I answer your question. Mike B.

THAD M LeisurePro has asked me to try to answer this question for you since I have bought one in the past, so here it goes! The fitting itself should fit since most inflator nipples are universal and are used in a number of applications. I have a rebreather and these fittings are in several locations on the rebreather itself, and also on my drysuit inflator. I find it to be advantageous to have things interchangable. As far as length goes, my advice is to put your rig on and have a friend use a peice of cord or string and trace to path the hose will be following, and then measure the string. Go with that length or the closest size longer. I prefer to have things as neat and tight as possible. It's important to be streamlined. Another thing to cosider is if you'll be using an alternate air source as your inflator. If that's the case, then you may want a little extra slack. In any case you can exchange it through LeisurePro easily if you find that it's not quite right. I hope this advice is helpful.----------Thad

MICHAEL B I would go for 22 inch hose for inflator. It'll lay much flatter and more flexible also.

JOHN A I would imagine it would work for you as it is a standard BCD inflator hose. Since it is Xsmall, I would go with less than 30"

Glenn o Hello - I purchased this hose for my Zeagle Stiletto BCD (BCD size large). The original hose was about 8 inches too long and this one is more to my liking / it fits better. The fittings are generic, I suppose if you are intending to use this as an lp inflator hose you'd be fine. I cannot, however, comment on an appropriate length as I am unfamiliar with your BCD model.

David R Yes, it would fit and the standard bc hose length is about 27"

OLIVER F Don't have a Cressi but I had to measure my Mares to find the right length

ROBERT W Yes,24+