GARY S I have limited experience with the Intova camera tray with flex arm. I did not use it enough to learn if the highest flash setting would provide more light or greater than 10 to 15 feet distance. I would think that more stobe or combination would provide more light and perhaps further distance.

GREG M Hi Mike, I can't really answer your question as I am not that well versed in all the ins and out of lighting/arms, etc. I have the base and flex arm but I just mount a good underwater flashlight on it and between the light and the flash I get what I get. LOL. Sorry I couldn't be more help to you. Greg You can check out my pictures on my website roatanwallpaper

GREG M Not sure if it will work for you but can give you the dimensions which may help you decide. It is somewhat adjustable. The center screw thead/size is standard so I don't believe that will be a problem. There are three separate positions (holes) the screw can go in with the widest dimension available being 4 and 3/4 inches (12 cm). My thought is that if you measure from the mounting hole (where the screw would go) to the outside edge of your camera housing and it is less than 4 and 3/4 inches it will work. Good luck. As far as quality is concerned, I am satisfied. I use it regularly with no problems. Check out my website (roatanwallpaper) for pictures I have taken with my camera equipped with this particular arm.

EDAN V It is has the universal camera thread mount so it will absolutely work with the S95 case.

GARY S Hi Laura, I believe the screw in the tray will fit most cameras and the only possible concern would be the dimensions of your camera case if it could be too wide to not touch the felx arm. I had some trouble with keeping every thing tight when taking out of the water storage can on the dive boat. If you check it before entry into the water is will probably work. Also mine has corroded slightly at the screw that joins the flex arm to the tray base. The result is that I have not been able to change the arm to the other side. I have not tried a lubricant to see if it will free up, but it would be a good idea to treat it with WD 40 or a silicone spray after a dive to prevent corrosion. Hope this helps! Gary

COREY M sorry, I'm using it with a housing from Sony, made by Sea & Sea. Don't know if it will work with Ikelite.

JEFFREY P Not sure about that case, but the bolt is the standard size of all tripod bolts. It fit my canon case perfectly and worked very well as good hand hold for underwater photos.

JOHN B Hi Laura R, If your camera case has a female fitting on its' base. I'm sure it is universal to accept tripods and other accessories, including this flex arm. Jack

JAMES L I got mine for a gopro camera but i would think it would fit the ikelite housing if it has a tripod screw on the bottom. If not, then no it wouldn't work.

JOSEPH M This is a universal mount. I've used mine on several differant camera cases. Never had any issues

J A S Laura.. I can't see the bottom of the Ikelite housing, but if there is a tripod screw (can't image there wouldn't be one), then this arm should work. I have a Fuji FD31 in its housing and this has served me well. Jay S.

JAMES S Hi Laura, I use it with a couple of different Canon cases, but not the Ikelite. It should work ok. I had a little trouble with one case becuase the bottom bracket would not sit flush with the housing, but a few modification with a metal file did the trick. Hope that helps. Regards, Jim

STEVEN K I am not sure specifically it will or will not work with your camera. I will tell you it is a generic mounting system that works will all of our other cameras , diving or not. If your case has a threaded receiver on it, I would be willing to bet it will work great.

LOWELL H yes it will work with that housing set up. If you want mine I used it once in Belize. $25 shipped. 9104090132

TREVOR D It should work with any camera or housing that has a standard tripod mount on the bottom.

ALAN P Works fine for my Nikon L18 in a Fantasea case.

ARTHUR M I bought this arm for a light to attach to my underwater movie camera. It met all of my needs at a very good price compared to all of the other arms I looked at. Hope this helps.

JAROMIRA N Yes it will work. It is pretty universal. It will accept 95% of smal cameras.

DAVID M The set screw/knob that holds the flex arm to the camera stay does seem to loosen up while diving. Its easy to re-tighten again while under water, how ever if you forget about it there is a chance the arm could come off. I'm sure there is an easy fix for it (if nothing else some sort of saftey wire/string in case the arm does separate from the stay). The arm/stay assembly worked very well and over all I was quite pleased with it and will soon be ordering a second one so I can use double lights. I tried both the narrow and wide angle Intova lights and got the best results using the wide angle light and aiming it slightly above my subject rather than directly on it. I would recomend this product for any underwater camera.

SCOTT S Yes, that is what I have for my camera case. My wife and I just got back from Cayman Brac, this was the first time I got to use the strobe arm and it was great. The only thing that I see that I might have to work on is the thumb screw. I will have to be changed it out so I can add more weight bars to get better neutral buoyancy in the water.

J A S It works for our Fuji F31D underwater case. I had to make a few "innovations" with that (nothing major - just some spacing) but other than that, it works great. I was given a tip by a full time underwater photographer to make the arm into a "C" shape back and over the camera. 1. It makes it easier to shot and have the flash in alignment with the lens, and 2. makes it easier to carry underwater. Seemed to work pretty well that way.

JEFF S works fine.. but you have to tighten the srews each time you go down... they don't fall off. they just get lose every once inawhile.... stu

LeisurePro S If you want to mirror exactly what comes in this kit, you will need one Intova Flex M extension arm and another Flex Arm.