800.637.6880
212.645.1234
|
|
Omer "Millennium" Full Foot Free Diving Fins
4
See More Similar
Scuba Fins, Snorkeling Fins, Swim Fins »
|
|
Omer "Millennium" Full Foot Free Diving Fins 12-13 (46-48)
|
List Price:
|
$160.00
|
|
Our Price:
|
$143.95
|
|
You Save:
|
$16.05 (10%)
|
SKU:
OSBFM
In Stock
|
|
|
Questions about this item:
Shopper Hi I have wide feet size 11.5 4E and will be wearing 5mm socks as the water temp only reaches the high 60's in summer where I live. Will these fins fit and what size would you recommend?
DINO S Sorry I haven't gotten back to you sooner. Our IT department has us blocked out of everything. I wear size 12 shoes and have a wide foot. Not sure if as wide as yours. But I have the 10-12 size and I can get in them with a 7mil sock with a little work. I wear 4 mil socks in the summer. Hope that helps.
ROBB S You'll have to try em on, try 43s. Good thing leisure pro has a good exchange policy!
CHRIS P HI,
I wear a size 9 Nike running shoe and my toe is about a 1/4 inch from the end of the shoe. My fins are size 42-43 / 7-8.5, and I use a 3mm sock. the foot pocket is wide, and with all of the Omer products I own I've been able to find a size that fits. I would advise you to buy a size that the size range starts at 11.5. If they are not right LeisurePro will exchange them for the right size. I have had these fins for 6 yrs and really put them to the test. Not one problem. Still kickin!!
NILZETE B I have size 10 feet and i wear 3mm neoprene socks and i bought the 42/44 and it fits me perfect, i used live and freedive in south florida so the water was warm . I hope this helps you, but its up to u to decide what size u wanna go with ...
JUSTIN B As for size, use the sizing chart. I'm pretty sure I got the largest size they had and I'm an 11. They were a bit lose even with socks so I used fin straps too.
JUSTIN B They felt quite true to size if perhaps a bit wide. I would say you are ok.
Shopper how do u take them apart ????
CARLOS R 1.- Unscrew the back of the fins.
2.- Using a flat screwdriver pull away the side clips.
3.- From the begining of the footpockets on both sides you can pull away the rubber insert from the blade.
4.- If you are looking for a good Real 100% Carbon Fiber Blade made In USA go online to DeepApnea
STEVEN M It may be two screws but it's very easy.
STEVEN M There's a phillips head screw underneath the ball of the foot area and the blade slides out of the two edge guides.
MIGUEL H you just slid out each rubber side. Then remove the two screws and slide the whole blade off. not hard to do but takes time.
RONALD R Remove the two stainless steel screws on the underside of the fin and then gently detach the fin from the rubber that wraps around the sides of the fin.
Matej V Hi I will be traveling with these fins quite often. So the travel size matters. I was wondering how difficult is to dismantle and assembly the footpockets and the blades?
Thank you
IVAN P You need a screwdriver to do it. Then it will take about 5 min either to assemble or to disassemble the fins
CHAD G I never dismantled mine, so unfortunately I can't answer that. I have traveled with them and just take them as a carry on and never had an issue with doing so.
RAYMOND J Hi Matej V: The blades can be removed from the foot pocket, but it is a bit difficult, at least at first. I'm sure after you do it a few time, it will be much easier. It might be a good idea to get a few extra clips, as they seem to be a little weak. Ray J
ANDY C I rarely take mine apart, make sure you grease the screws. They come apart easily.
Andy Campbell
ROY P I have never disassembled mine, but I doubt it would make them much smaller to pack since the blades come all the way back to the foot pocket.
in any case these are great fins, I do a lot of spear fishing and after almost 7 years, I am very happy with them.
hope helpful,
TP
BRANKO F It is very easy. Check the type of screw driver that you need and keep it handy.
BJOERN K won't take you longer than 1 min/fin. love these fins.
GENE M R It is not very difficult. You will have to carry a screw driver with you to remove the 2 scres holding the blade in. I have found that the blade clips require a little muscle to get on and off, but seem to hold very well. My suggestion; as i often do when i dont have my big speargun case, is carry them on the plane as my attache! your allways allowed a carry on and a "purse" type bag. I make my fins this bag and stick them inthe overhead compartment. They fit real well!
JOHN P It is a pain to do it every time. I did it once. The next time I carried them on my back pack and on the plane. The last several times I packed them in the suitcase putting the tips down and then bending them. They straightened back out in an hour. They are awesome fins.
ANDY C I love my fins, lots of power. I'd recomend them to any and all. Andy campbell
HENRY K hmmm it's possible
on the 1-10 hassle scale I would say a 6
you need exactly the correct size screwdriver
and you might want to lube the rails lightly with silicone
I just check my free dive gear in the biggest checkable soft duffle
with the fins intact, inside a fin bag, in the duffle, wrapped in the wetsuit
HK
Shopper I wear a size 12 men's. What would the best size for me? Should I get a sock as well?
LeisurePro S I would recommend the 10-12. Socks are optional with these closed heeled fins, but lots of people who have them like to wear socks to cut down on rubbing.
Shopper I wear a 10.5 - 11 shoe and will be wearing these fins WITHOUT socks in tropical waters. Would the 9-10 be too small?
LeisurePro S I think the 9-10 should work out fine without a sock.
Shopper hello =) i am interested in purchasing the omer millenium fins but do not understand the sizing listed on your site, i am a US 10.5-11 depending on the shoe, which size does this correspond to and what thickness of sock should i get to accompany the fin?
LeisurePro S You are a size large in these fins, a 3 mm sock like the Blue Reef 3mm Neoprene Sock should fill in any extra space and keep you comfortable.
Shopper i was just wondering what the standard size of these fins are, ie does a large mean a mens U.S. 10-11? mahalo
Warranty Information
This product has a limited warranty of 24 months.
www.omerdiving.com
(800) 853-1911
Whats in the box:Pair of Omer "Millennium" Full Foot Free Diving Fins The Standard Stiffness Millennium Non Vented Blades are manufactured in Black Polypropylene Plastic. The Blades are (L x W) 29.4"x 8.8" (746 x 223 mm), with a Variable Thickness from 0.2" to 0.1" (5.0 to 3.0 mm). The Millennium Fins are suitable for all around Free Diving at Depths of less than 80' (24.38 meters). Omer's Interchangeable Foot Pocket has been designed and developed internally by Omer's Technicians and it is manufactured with newest Rubber Compression Molding Technologies existing today. The Foot Pocket is produced with Natural Rubber in Two-Different Stiffness Compounds to Maximize the Efficiency of the Stroke without Compromising Comfort. The Internal Geometry of the Foot Pocket, with the use of Beta Tools in the production of Safety Shoes, has been Ergonomically designed to Fit with Total-Comfort. The Blade design Optimizes Canalization of Water on its Surface and Maximum Impact Resistance at the Blade Edges. Three Reinforcing Ribs have been added under the Heel to Increase the Stroking Power. The Omer Millennium Fins are available in US sizes 6-7, 8-9, 9-10, 10-12 or 12-13 (EUR: 38-40, 40-42, 42-44, 44-46 or 46-48) is Black in color and is covered by a 24 month limited warranty.
- Omer "Millennium" Full Foot Free Diving Fins:
- Standard Stiffness Millennium Non Vented Blades
- Blade Material: Black Polypropylene Plastic
- Suitable for Free Diving at Depths of Less than 80' (24.38 meters)
- Interchangeable Foot Pocket
- Foot Pocket: Newest Rubber Compression Molding Technologies
- Foot Pocket: Natural Rubber in Two-Different Stiffness Compounds
- Dual Stiffness: Maximize the Efficiency of Stroke w/o Compromising Comfort
- Internal Geometry of the Foot Pocket: Beta Tools Used in Production of Safety Shoes
- Ergonomically Designed to Fit with Total-Comfort
- Blade Design Optimizes Canalization of Water on its Surface and Maximum Impact Resistance at Blade Edges
- Three Reinforcing Ribs Under Heel Increases Stroking Power
- Sizes US: 6-7, 8-9, 9-10, 10-12 or 12-13
- Sizes EUR: 38-40, 40-42, 42-44, 44-46 or 46-48
- Blade Dimensions (L x W) 29.4"x 8.8" (746 x 223 mm)
- Blade Thickness: (Variable) 0.2" to 0.1" (5.0 to 3.0 mm)
- Color: Black
- 2 Year Limited Warranty
| Materials | Blade: Polypropylene Plastic
Foot Pocket: Rubber | | Dimensions | (L x W) 29.4"x 8.8" (746 x 223 mm)
Thickness (Variable) 0.2" to 0.1" (5.0 to 3.0 mm) | | Blade Type | Non-Vented | | Open Heel/Full Foot | Full Foot | | Weight [with packaging] | 6-7 (38-40): 4.95 lb, 9-10 (42-44): 5.15 lb, 8-9 (40-42): 5.3 lb, 10-12 (44-46): 5.75 lb, 12-13 (46-48): 6.55 lb |
By protenek from Tampico, Mexico - Sizing:
- Feels true to size
- Width:
- Feels too wide
- Was this a gift?:
- No
By seahorse from Boulder, CO - Sizing:
- Feels half size too small
- Width:
- Feels true to width
- Was this a gift?:
- No
3/30/2011 5.0Good fins my second set By Sheetsy from Rhode Island About Me Casual/ Recreational - Sizing:
- Feels true to size
- Width:
- Feels true to width
- Was this a gift?:
- No
9/20/2010 4.0"a good product for the money" By P.R.viking spearos from dorado puerto rico - Sizing:
- Feels half size too big
- Width:
- Feels true to width
- Was this a gift?:
- No
1/7/2010 5.0excelent for the price you pay By Luis Fonseca from Margarita island - Sizing:
- Feels true to size
- Width:
- Feels true to width
|
|
Related products for Omer "Millennium" Full Foot Free Diving Fins 12-13 (46-48)
|
The Standard Stiffness Millennium Non Vented Blades are manufactured in Black Polypropylene Plastic. The Blades are (L x W) 29.4"x 8.8" (746 x 223 mm), with a Variable Thickness from 0.2" to 0.1" (5.0 to 3.0 mm). The Millennium Fins are suitable for all around Free Diving at Depths of less than 80' (24.38 meters). Omer's Interchangeable Foot Pocket has been designed and developed internally by Omer's Technicians and it is manufactured with newest Rubber Compression Molding Technologies existing today... more
Tags: Essential Equipment,Omersub Full Foot Freediving Fins,Full Foot Fins,Omer "Millennium" Full Foot Free Diving Fins 10-12 (44-46),Omer,Millennium Diving Fins,Omersub Diving Fins,Fins,Omersub,Full Foot Freediving Fins,Diving Fins,Omersub Millennium
|
The Eagle Ray Free Diving fins feature a synthetic rubber foot-pocket with an excellent quality price relationship. The blades are produced in a low modular polypropylene with a 17?angle between the foot-pocket and blade. It's a powerful fin yet comfortable and easy to use, ideal for beginners as well as skilled divers. Fins are available in 4 sizes from US 8-9 to 12-13 (EUR 40-41 to 46-47).... more
Tags: OSBFER46, Omer, Fins, Essential Equipment, Omer Eagle Ray Full Foot Fins 12-13 46-47
|
Cressi introduced the Gara Modular Non-Vented Fin in 2012. Its Long Blade with Foot Pocket System makes this a perfect choice for Deep Free Diving and Spear Fishing and for Divers of all levels. The Interchangeable Blade allows the Diver to replace the Interchangeable Blade for Specific Diving Situations which makes this Fin perfect to grow with as the Diver's Skill Level Increases. Any of Cressi's Long Fiberglass or Carbon Fiber Blades can be Interchange in minutes without any modifications... more
Tags: CSBFGM12, Cressi, Fins, Essential Equipment, Cressi Gara Modular Fins 12-13 46-47
|
After the great success of the Gara Professional and the Gara 3000 LD Cressi has combined the two designs and characteristics into the Gara Professional LD. The Blade is made from a special Elastomer Polypropylene which gives a Longer Lasting, more Fluid, and Softer Kick that is less demanding, making it ideal for covering long distances. The use of this New Plastic is less Reactive than the Compoflex used in the Gara Professional. It is a Progressive and Controlled Blade, with Flexibility and gives an Extremely Fluid Kick. Together with the Exceptional Lightness and Non-Dispersion of Effort... more
Tags: CSBFGPL12, Cressi, Fins, Essential Equipment, Cressi Gara Professional LD Fins 12-13 46-47
|
Reaction Pro is the most recent Cressi Full Foot Non-Vented Fin which has been developed after the Rondine. The Reaction Pro is an innovative fin in look and performance. The Reaction is molded using the exclusive and patented Cressi system with 3 materials. The three materials consist of a comfortable thermo-rubber (elastomer) anatomic, computer-designed foot pocket. The foot pocket encompasses the foot assuring transmission of the leg-to-fin thrust without loss of energy, adding efficiency to the fining action... more
Tags: CSBFRP12BK, Cressi, Fins, Essential Equipment, Cressi Reaction Pro Full Foot Fins 12-13 Black
|
The new Stingray Carbon fins feature carbon fiber blades manufactured using the infusion technology with innovative double vacuum process. Thanks to this technology the carbon fiber stands are impregnated perfectly in the resin without the risk of forming micro bubbles and with an optimal distribution of the resin itself. In addition the percentage of necessary resin is reduced considerably more than before with a great increase in performance characteristics of the blade. The specific carbon fiber strand used was developed specifically for the manufacture of free diving fins and patented... more
Tags: OSBFS45, Omer, Fins, Essential Equipment, Omer Stingray Full Foot Fins 11-12 45-46
|
|
|